ADIADUCM360数据采集系统解决方案

Power Consumption

MCU Active Mode: Core consumes 290μA / MHz

Active Mode: 1.0mA (All peripherals active), core operating at 500KHz

Power down mode: 4μA (WU Timer Active)

On-Chip Peripherals

UART, I2C and 2 x SPI Serial I/O

16-bit PWM Controller

19-Pin Multi-Function GPIO Port

2 General Purpose Timers

Wake-up Timer/Watchdog Timer

Multi-Channel DMA and Interrupt Controller

Package and Temperature Range

48 lead LFCSP (7mm x 7mm) package –40℃ to 125℃

Development Tools

Low-Cost QuickStart™ Development System

Third-Party Compiler and emulator tool Support

Multiple Functional Safety features for improved diagnostics

ADuCM360/1应用:

Industrial automation and process control

Intelligent, precision sensing systems

4 mA to 20 mA loop-powered smart sensor systems

Medical devices, patient monitoring

图1. ADuCM360方框图

ADUCM360/361开发系统

The ADuCM360/ ADuCM361 is a low power fully integrated, 24-bit data acquisition system incorporating dual, high performance multi-channel sigma-delta (Σ-Δ) ADCs, ARM Cortex M3® MCU, and Flash/EE memory on a single chip.

ADI provides low cost development platforms for the Cortex M3 based ADuCxxx microcontrollers.

The hardware is designed for simplicity, flexibility and ease of use. This facilitates performance evaluation of the device with the minimum external components. The supplied interface and Jlink Lite boards connect to the miniboard, providing supply, UART communication and debug capability.

The QuickStart Plus Kit for the ADuCM360/361 Precision Analog Microcontrollers features true non-intrusive JTAG emulation and an assembly & C-source debugging environment. This provides a comprehensive hardware development environment.

QuickStart Plus Kit Contents:

Hardware Contents:

Evaluation Board

USB Cables

J Link Lite

Interface Board

Software Contents:

Keil MDKARMevaluation version integrated software development tool

IAR EWARM evaluation version integrated software development tool

CM3WSD Serial Downloader

Example Code

Function Libraries

Get Started User Guide

Datasheets, Application Notes, Etc.

debugging environment. This provides a comprehensive hardware development environment.


图2. ADUCM360/361开发系统外形图

图3. ADUCM360评估板电路图

图4. ADUCM360评估板PCB布局图:顶层

图5. ADUCM360评估板PCB布局图:底层

详情请见:
http://www.analog.com/static/imported-files/data_sheets/ADuCM360_361.pdf

峰值电流型BUCK的MATHCAD计算 这里再给大家介绍一下峰值电流型BUCK的计算，峰值电流型BUCK和电压型BUCK是目前IC采用得比较多的控制方法，当然另外还有
COT(constant on time)，OCC(one cycle control)等等..

如何处理高 di/dt 负载瞬态就许多中央处理器 (CPU) 而言，规范要求电源必须能够提供大而快速的充电输出电流，特别是当处理器变换工作模式的时候。例如，在 1V 的系统中，100 A/uS 负载瞬态可能会要求将电源电

基于示波器的电源纹波的测试分析       一、什么叫纹波？
　　纹波（ripple）的定义是指在直流电压或电流中，叠加在直流稳定量上的交流分量。

　　它主要有以下害处：

　　1.1．容易在用电器上产生谐波，而谐波

大电流电感

 3/3   首页 上一页 1 2 3