Connecting dual-digit LED modules

Abstract: The MAX6954/MAX6955 LED display drivers allow users to drive both individual LED digits and插件电感 shared segment pins. This application note details what steps must be taken to map the digits properly.

<-- ======================================================================= --><-- CONTENT: DB HTML --><-- ======================================================================= -->Maxim's MAX6954 and MAX6955 LED display drivers can be used to drive LED digits whose segment pins are individually available. The MAX6954/MAX6955 can also be used to drive dual-digit 7-segment LED modules which feature shared segment pins. Figure 1 shows the internal example configuration of such a device.


Figure 1. Internal configuration of a dual-digit LED module.

Up to eight dual-digit modules or 16 digits can be driven by just one MAX6954 or MAX6955. The following module digit-to-digit mapping is recommended to connect these modules to the MAX6954/MAX6955.

Module1-Digit1 -> Digit 0               DIG1 -> CC00           
Module1-Digit2 -> Digit 1               DIG2 -> CC01           

Module2-Digit1 -> Digit 2               DIG1 -> CC02          
Module2-Digit2 -> Digit 3               DIG2 -> CC03          

Module3-Digit1 -> Digit 4               DIG1 -> CC04           
Module3-Digit2 -> Digit 5               DIG2 -> CC05          

Module4-Digit1 -> Digit 6               DIG1 -> CC06           
Module4-Digit2 -> Digit 7               DIG2 -> CC07          

Module5-Digit1 -> Digit 0a       	DIG1 -> CC00        
Module5-Digit2 -> Digit 1a              DIG2 -> CC01           

Module6-Digit1 -> Digit 2a       	DIG1 -> CC02           
Module6-Digit2 -> Digit 3a     	 	DIG2 -> CC03           

Module3-Digit1 -> Digit 4a              DIG1 -> CC04           
Module3-Digit2 -> Digit 5a              DIG2 -> CC05          

Module4-Digit1 -> Digit 6a              DIG1 -> CC06           
Module4-Digit2 -> Digit 7a              DIG2 -> CC07 

Table 4, Connection Scheme for Sixteen 7-Segment Digits, in the MAX6954/MAX6955 data sheet explains that digit 0, 1, 2, 3, 4, 5, 6, and 7's segment pins are identified by 1a, 1b, 1c, 1d, 1e, 1f, 1g, and 1dp; digit 0a, 1a, 2a, 3a, 4a, 5a, 6a,and 7a's segment pins are identified by 2a, 2b, 2c, 2d, 2e, 2f, 2g, and 2dp.

The scan limit should be set accordingly by writing the proper number to register 0x03. For this example with al塑封电感器l eight modules or 16 digits, the scan-limit register should have a content of 0x07. The scan-limit register content can be changed to 0x03 if only four modules or eight digits are driven. Wh一体电感en only half of the modules or digits are used, the module digit-to-digit mapping can be changed to the following.大功率电感贴片电感器

Module1-Digit1 -> Digit 0               DIG1 -> CC00           
Module1-Digit2 -> Digit 1               DIG2 -> CC01           

Module2-Digit1 -> Digit 2               DIG1 -> CC02          
Module2-Digit2 -> Digit 3               DIG2 -> CC03          

Mod电感器市场需求ule5-Digit1 -> Digit 0a       	DIG1 -> CC00        
Module5-Digit2 -> Digit 1a              DIG2 -> CC01           

Module6-Digit1 -> Digit 2a       	DIG1 -> CC02           
Module6-Digit2 -> Digit 3a       	DIG2 -> CC03

电源设计的十个相关电路概念1、整流桥并联在小功率设计中，一般很少用到整流桥的并联，但在某些大功率输出的情况下，不想增添新的器件单个整流桥电流又不满足输入功率要求，就需要用到整流桥的并联了，整流桥的并联不能采用两个整流桥各自整流后直流并联的方式，也就是不能采用图1的方式，因为整流桥没有配对，单纯靠自身的V-I特性，一般是无法均流的，这样就会造成两个整流桥发热不一致。 而采用图2的方式，通常认为在一个封装内的两个二极管是非常匹配的，是可以均分电流的，所以采用

聚酞亚胺微细加工技术传统的绝缘层形成技术是采用涂料器将感光性聚酞亚胺树脂涂敷，经曝光、显影等得出图形后，在高温长时间进行固化处理，造成生产成本增高。同时，在进行化学蚀刻加工时，聚酸亚胺基材易

变压器驱动波形我的变压器驱动电路如图所示,但是输出的驱动波形很难看,而且芯片SG3526的输出PWM信号在峰值的后半段,有个下降,不知道这是什么原因造成的,恳求高手帮忙! 2784541236391968.s